Providing advanced imaging products, embedded systems and solutions

Product image of the HDMI Autofocus Zoom Block Camera with Tamron MP1110M

Click image to enlarge

HDMI AF-Zoom Block Camera with Tamron MP1110M

Part Number: AS-CIB-HDMI-001-1110-A | AS-CIB-HDMI-001-1110WP-A

  • HDMI camera solution for the Tamron MP1110M-VC and MP1110M-WP.
  • 10x optical zoom, 16x digital zoom.
  • 1/3-type CMOS progressive scan image sensor.
  • Supports all HD modes up to 1080p60.
  • Remote camera control (VISCA) via TTL comms port.
  • Video output mode selected by DIP switches or VISCA control.
Enquire About This Product
  • Description

  • Product Specs

  • Downloads

Description

Products Specs

Downloads

The HDMI AF-Zoom Block Camera offers 10x optical zoom and 16x digital zoom with HDMI output.

This lightweight camera solution is extremely compact, measuring only 34.7 x 41.5 x 58.4mm and weighing only 81g. It is a high image-quality camera module with SMPTE 274M and SMPTE 296M compliant video output up to 1080p60 Full HD.

The HDMI output is enabled when an HDMI cable is connected. On power-up, the camera video mode may be selected by the DIP switch settings on the board. Camera video modes, along with other camera and interface board functions, may also be controlled by TTL, RS-232 or RS-485 serial communication.

Benefiting from Tamron’s high quality optical design and low reflection coating technologies, the camera offers Wide Dynamic Range mode, 3D noise reduction, keystone correction, motion detection and many other sophisticated camera features.

The Tamron MP1110M-VC and -WP cameras are also available with HDMI/USB or 3G-SDI video output.

Camera Specification

Image sensor

1/3-type CMOS (progressive scan)

Effective no. of pixels

Approx. 4,080,000 pixels

Pixel output (H x V)

1920 x 1080; 1280 x 720

Video format (HD)

1080p/60, 1080p/59.94, 1080p/50, 1080p/30, 1080p/29.97, 1080p/25, 1080i/60, 1080i/59.94, 1080i/50, 720p/60, 720p/59.94, 720p/50, 720p/30, 720p/29.97, 720p/25

Video format (SD)

NTSC / PAL

Minimum illumination

0.5lx (1/30 sec, F1.8, 50%)

Recommended illumination

100lx to 100,000lx

S/N ratio

More than 50dB

Gain

Auto / manual

Shutter speed

1/1 to 1/10,000 sec

Sync system

Internal

Exposure compensation

-12dB to +12dB (total 13 steps)

Backlight compensation

ON / OFF

Gamma

Standard / straight

Aperture control

16 steps

White balance

ATW1 (narrow), ATW2 (wide), one push, manual (B, R)

AE (Auto exposure mode)

Auto, manual, priority mode (shutter / iris)

Lens (wide to tele)

10x optical zoom f=3.3 to 33.0mm F1.8 to 3.4

Zoom mode

Standard / variable / direct

Zoom movement speed (wide to tele)

1.4 sec (focus tracking ON)

Digital zoom

Up to 16x

Focusing system

Auto, manual, one push, AF sensitivity

Horizontal viewing angle (wide to tele)

59.2° to 6.7°

Minimum object distance (wide to tele)

10mm to 800mm

Horizontal resolution

800 TV lines

Connector Specification

KEL30 Connector (J1)

The interface board is fitted with a 30-way miniature connector to link to the matching connector on the camera.

Connector type: KEL USL00-30L.

Mating cable: A 30-way micro coaxial cable (AS-CIB-USL30-100MM) is supplied with the camera. Lengths available: KEL USL20-30SS-010-C (100mm length) or KEL USL20-30SS-005-C (50mm length).

Input/Output Connector (J2)

The interface board is fitted with an industry standard 4-way connector for VSync signal output and test pattern/reset control inputs.

Connector type: JST SM04B-SRSS-TB

Mating cable: A suitable cable is available as part of the cable kit AS-CIB-CBLKIT-003-A (see ordering information below).

See Harrier HDMI Camera Interface Board datasheet for pin assignments and control options.

Power and Control Connector (J3)

The interface board is fitted with an industry standard 10-way connector for power and serial control.

Connector type: JST SM10B-SRSS-TB

Mating cable: A suitable cable is available as part of the cable kit AS-CIB-CBLKIT-003-A (see ordering information below).

See Harrier HDMI Camera Interface Board datasheet for pin assignment and output options.

JTAG Connector (J4):

The interface board is fitted with a micro HDMI display output connector. HDMI output is active when an HDMI cable is connected.

Connector type: HDMI Type D (micro).

Mating Connector: Standard micro HDMI cable.

HDMI Output Connector (J5)

The interface board on the camera is fitted with a micro HDMI display output connector. HDMI output is active when an HDMI cable is connected.

Connector type: HDMI Type D (micro).

Mating Connector: Standard micro HDMI cable.

Video Mode DIP Switch (SW1)

The interface board is fitted with an 8-way DIP switch (SW1) to enable selection of camera video format on power-up. Switches 5-8 are reserved for future use. See datasheet for the configuration of the DIP switch elements.

Functions

VC (Vibration Compensation)

Available

Wide-D

Available

Defog

Available

Noise reduction (3D + 2D)

Available

Digital output

Available

Privacy zone masking

Available

Motion detection

Available

Slow shutter

Available

Picture effects (black white)

Available

Picture freeze

Available

Electronic flip (e-flip)

Available

Mirror image

Available

Temperature readout

Available

Title display

Available

Test pattern

Available

4:3/16:9 analog output

Available

Crosshairs

Available

General

Power requirement

8V to 12V DC

Power consumption

3.3W – Typical power with static view at 1080p60, values will vary with camera mode and with camera focus/zoom motor operations.

Operating temperature

0°C to +60°C (ambient environment).

Storage temperature

-40°C to +60°C

Operating humidity

20% to 80% (no condensation)

Storage humidity

20% to 90% (no condensation)

Dimensions (W x H x D)

34.7mm x 41.5mm x 58.4mm (w x hx d)

Weight

Approx. 81g

Status LED

The interface board is fitted with a multi-color LED to indicate camera status.

Ordering Information

Part number Description

AS-CIB-HDMI-001-1110-A

Tamron MP1110M-VC autofocus zoom camera with Harrier HDMI interface board AS-CIB-HDMI-001-A attached with AS-CIB-USL30-100MM connecting cable.

AS-CIB-USBHDMI-001-1110WP-A

Tamron MP1110M-WP autofocus-zoom camera with Harrier HDMI interface board AS-CIB-HDMI-001-A attached with AS-CIB-USL30-100MM connecting cable.

AS-CIB-USBHDMI-001-EVAL-A

Evaluation Kit for Harrier HDMI and Harrier USB/HDMI Camera Interface Board. Includes power supply, cabling (including AS-CIB-CBLKIT-002-A) and PC serial interface (via USB UART).

AS-CIB-CBLKIT-003-A

Cable kit for AS-CIB-HDMI-001-A containing cables for J2, J3, and J4 that connect to the Harrier Evaluation Board.