Cameras

Harrier 36x AF-Zoom HD-SDI Camera with Global Shutter

Part Number: AS-CIB-HDSDI-002-36LGHD-A
Product image of the Harrier 36x AF-Zoom Camera with HD-SDI output

Features

  • Full HD autofocus-zoom camera with HD-SDI output.
  • 1/2.3-type Sony Pregius IMX392LQR-C CMOS sensor (global shutter).
  • 36x Optical Zoom & 32x Digital Zoom.
  • Supports 1080p – 30/25 fps, 720p – 60/50/30/25 fps.
  • HD-VLC™ output mode for long cable length applications.
  • TTL/RS-232 Serial VISCA, Pelco – D/P Control Protocol.
  • Single VISCA programmable 3.3V PWM output channel.
  • Video mode selection switches and built-in test pattern.
  • External trigger and strobe out capability.
  • Simultaneous analog (PAL/NTSC) when in 720p50/59.94/60 modes.

The Harrier 36x AF-Zoom HD-SDI Camera is equipped with a powerful 36x optical zoom (32x digital zoom) and a Sony Global Shutter CMOS sensor. The global shutter allows the capture of moving objects without the distortion which can occur with rolling shutters.

In addition to HD-SDI, the camera also provides simultaneous analog output in Standard Definition (SD) video and supports HD-VLC™ output mode for long cable length applications.

Serial VISCA over TTL, RS-232 and RS-485 or Pelco-D/P Control Protocol are available to control the camera. DIP switch settings control the selection of serial communication protocol, HD-VLC output and camera video output mode on power-up.

Special features of the camera include Digital Image Stabilization, Noise Reduction, Privacy Mask Function, Intelligent Motion Detection, Day & Night mode (Infrared Cut filter Removal, ICR) and High/Back Light Compensation (HLC/BLC).

The Harrier 36x AF-Zoom Camera is also available with USB (UVC) and/or HDMI output instead of HD-SDI. For more information contact our team.

Camera Specification

Image sensor

1/2.3-type Sony Pregius IMX392LQR-C CMOS sensor (global shutter)

Effective no. of pixels

Approx. 2,350,000 pixels

Video format (HD)

HD-SDI: 1080p/30/25 fps, 720p/60/50/30/25 fps
Camera LVDS: 1080p/60/50/30/25 fps (single LVDS mode), 720p/60/50/30/25 fps

Analog resolution

CVBS

Minimum illumination

Color(1/30s, 48dB) : 0.3 lux , Color DSS(1/2s, 48dB) : 0.06 lux

S/N ratio

more than 50dB (AGC off)

Gain control (AGC)

0 – 10 steps

Shutter speed

1/30(25) – 1/20,000 sec

Sync system

Internal

DSS

Off / 2x / 4x / 8x / 16x / 32x (/64x : 60 or 50fps mode only)

White balance

Auto, One Push, Manual, Indoor, Outdoor

AE (Auto exposure mode)

Auto, lris Priority, Shutter Priority, Manual

Lens (wide to tele)

Optical x36 Zoom, f=6mm to 216mm, F1.5 (wide) to F4.8 (tele)

Digital zoom

OFF / MAX 1x – 32x

Focusing system

Auto / One Push / Manual

Viewing angle (FOV)
FOV D H V
Wide 59.1° 52.6° 31.1°
Tele 2.3° 2.0° 1.1°
Minimum object distance (wide to tele)

100mm (wide) to 1500mm (tele)

Control protocol

Serial VISCA
Pelco-D / Pelco-P

Baud rate

9600 / 19200 / 38400 / 115200

Camera Functions

Day & Night mode

Day / Night

Digital Noise Reduction

OFF / Low / Middle / High / Auto

Digital Image Stabilization

Available

High/Back Light Compensation (HLC/BLC)

Off / BLC / HLC

Defog

Available

Motion detection

Detection OFF / 3 positions

Privacy mask

Mask OFF / 8 positions

Defect detection

Detection ON/OFF

Connector Specification Harrier 3G-SDI Camera Interface Board

KEL30 Connector (J1)

The interface board on the camera is fitted with a 30-way miniature connector to link to the video output connector on the camera.

Connector type: KEL USL00-30L.

Mating cable: A 30-way micro coaxial cable (AS-CIB-USL30-100MM) is supplied with the camera. Lengths available: KEL USL20-30SS-010-C (100mm length) or KEL USL20-30SS-005-C (50mm length).

Input/Output Connector (J2)

The interface board is fitted with an industry standard 4-way connector for Vsync/PWM signal output and test pattern/reset control inputs.

Connector type: JST SM04B-SRSS-TB

Mating cable: A suitable cable is available as part of the cable kit AS-CIB-CBLKIT-002-B (see ordering information).

See Harrier 3G-SDI Camera Interface Board datasheet (download tab) for pin assignments and control options.

Power and Control Connector (J3)

The interface board on the camera is fitted with an industry standard 9-way connector for power, serial control and analog video out.

Connector type: JST SM09B-SRSS-TB

Mating cable: A suitable cable is available as part of the cable kit AS-CIB-CBLKIT-002-B (see ordering information).

See Harrier 3G-SDI Camera Interface Board datasheet (download tab) for pin assignments and output options.

3G-SDI Output Connector (J5)

The interface board is fitted with a Hirose H.FL Micro Coaxial Connector (75 Ohm).

Connector type: Hirose Micro Coaxial Connector (Receptacle), part number H.FL-R-SMT(01).

Mating connector: Use mating cable with 75 Ohm characteristic impedance, for example Hirose part number H.FL75-2LP-084H-A-100. A suitable cable is available as part of the cable kit AS-CIB-CBLKIT-002-B (see ordering information).

Analog Video Out (Pin 3, J3)

Standard resolution composite analog is simultaneously available in HD modes 720p50 (for PAL) and 720p60/59.94 (for NTSC). There are two options for the analog output, selectable via serial control:

(a) the 1280 pixel wide HD image can be cropped to 960 wide, by cropping a 120 pixel strip off each side to make a 4:3 aspect ratio Standard Definition (SD) signal.

(b) by pre-warping the image, such that when displayed on a HD monitor in the monitor’s stretch-to-fit mode, the original full-width HD signal will be displayed correctly at 16:9 aspect ratio.

Both methods ensure the displayed pixels remain square and that the image is not distorted.

Video and Control Mode DIP Switch (SW1)

The interface board is fitted with a 4-way DIP switch to select various video output and control modes.

The DIP switches to select the Video Format are read on power-up only. Therefore, to change mode using the DIP switches, power down the camera, set the switches and then power up the camera. DIP switches will only be effective for the operating modes supported by the camera currently in use.

See Harrier 3G-SDI Camera Interface Board datasheet (download tab) for the configuration of the DIP switch SW1.

Communications Mode Selection (SW2)

The interface board is also fitted with a 2-way DIP switch to select the serial communications standard. It allows to choose between RS-232 VISCA communications, RS-485 VISCA comms with RS-485 termination enabled, RS-485 VISCA comms with RS-485 termination disabled and TTL VISCA communications.

See Harrier 3G-SDI Camera Interface Board datasheet (download tab) for the details and configuration of the DIP switch SW2.

Digital Transmission Standard Selection (SW3)

The interface board is fitted with a 1-way DIP switch to select the SMPTE or HD-VLC digital output standards.

OFF = SMPTE compliant output.

ON = HD-VLC compressed output.

General

Power requirement

9 – 15V DC

Power consumption

7.6W (typical)

Operating temperature

-5°C to +50°C

Storage temperature

-20°C to +60°C

Operating humidity

0% to 90% (no condensation)

Dimensions (L x W x H)

138 x 55.6 x 65.5mm

Weight

450g

Part number Description
AS-CIB-HDSDI-002-36LGHD-A

Harrier 36x AF-Zoom HD-SDI Camera; includes 100mm 30-way micro-coax cable AS-CIB-USL30-100MM, 50mm available upon request.

AS-CIB-3GSDI-002-EVAL-B

Evaluation Kit for Harrier 3G-SD, including the Harrier 36x AF-Zoom HD-SDI Camera. The kit contains power supply, cabling (AS-CIB-CBLKIT-002-B), 30-way micro-coax cable (AS-CIB-USL30-100MM, for connecting camera with camera interface board) and the Harrier Evaluation Board with PC serial interface (via USB UART). Not included: Camera and camera interface board.

AS-CAM-36LGHD-A

Harrier 36x AF-Zoom Camera with global shutter sensor.

AS-CIB-3GSDI-002-A

Harrier 3G-SDI Camera Interface Board. 3G-SDI and HD-SDI interface solution for autofocus-zoom block cameras. Analog composite output (when in 720p50/59.94/60 operating modes). Support for HD-VLC compression technology. Board only, no cables included.

AS-CIB-CBLKIT-002-B

Cable kit for AS-CIB-3GSDI-002-A containing H.FL micro coax cable, BNC adapter and control cables for J2 and J3.

AS-CIB-USL30-100MM

30-way micro-coax cable for connecting the interface board (J1) to the camera. Length 100mm (Manufacturer: KEL, part number: USL20-30SS-010-C).

AS-CIB-USL30-50MM

30-way micro-coax cable for connecting the interface board (J1) to the camera. Length 50mm (Manufacturer: KEL, part number: USL20-30SS-005-C).

AS-CIB-BRK-007-A

Metal bracket, screws and spacers for mounting the AS-CIB-3GSDI-002-A to a Harrier 36x AF-Zoom Camera.

 

HD video transmission over long distances

If you're looking for long cable length solutions that guarantee high quality HD video transmission over greater distances we recommend HD-VLC technology. Check out our white paper on Long-reach HD video transmission technologies and this video:

 

Harrier Autofocus-Zoom Cameras

Watch this video to learn more about Harrier AF-Zoom cameras:

Related Products

View Product Camera Interface Boards
Harrier 3G-SDI Camera Interface Board (75 Ohm) product image

Harrier 3G-SDI Camera Interface Board (75 Ohm)

View Product
View Product Accessories & Cables
Photo of content and case of the evaluation kit for Harrier 3G-SDI

Evaluation Kit for Harrier 3G-SDI

View Product
View Product Software
Logo HarrierControl software and image of GUI

HarrierControl Camera Software

View Product
View Product Video Adapters
Product image - BlueBird SDI Adapter board

BlueBird SDI Adapter

View Product
View Product Video Adapters
Product image - BlueBird SDI Adapter enclosed version

BlueBird SDI Adapter – Enclosed Version

View Product
View Product Cameras
Product image of the Harrier 36x AF-Zoom Camera with Global Shutter

Harrier 36x AF-Zoom Camera with Global Shutter

View Product